Call Today

Have you been searching for info about Tools You Need to Install a New Bathtub ?

Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately tough job. If the old tub is readily accessible, the project can relocate easily; if you need to open up a wall to remove the old bathtub as well as position the new bath tub, the job is much harder. In either case, the task is within a house handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have qualified yourself for the task and also are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed project, it is far better to think about utilizing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This article will help you install a brand-new bath tub in your restroom if you have already acquired a brand-new tub and do not need to alter the plan of your previous water supply pipelines.
Your tools as well as material list must comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Getting ready for the Setup

To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last placement.

Removing Old Taps

If you need to change old faucets with new ones as a part of your installment, then the first thing you must do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipes have actually been gotten rid of, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

Installing the Tub

Using the two wood boards under its feet, put the tub in the needed setting. The wooden boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little factors.
The next objective is to ensure that the bath tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the tub until the spirit level reads degree.
To mount taps, fit all-time low of the outermost adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the same for the various other faucet.
Switch on the supply of water as well as check all joints as well as new pipework for leaks and also tighten them if needed. Fill the bath tub as well as additionally inspect the overflow electrical outlet and also the regular outlet for leakages.
Lastly, repair the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bath tub ought to wait until the tub has actually been made use of a minimum of once as this will settle it right into its final setting.

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washers are in location between the tap and also the sink. Safeguard the faucet in place with the supplier given backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous type should be attached to the faucet ends initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

Tiling Around the Bath tub

In the location where the bathroom satisfies the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to fracture a stiff seal, creating the water to permeate the wall between the bathroom and also the tiling, bring about problems with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are sold in tubes and also cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water before sealing, to permit the activity experienced when the tub remains in usage. The sealant can crack rather early if you do not take into account this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally easily available on the market. It is suggested to fit the floor tiles making use of water-resistant or water resistant sticky and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Do you enjoy reading up on How to Install a Bathtub Yourself? Put a remark down below. We would be interested to see your opinion about this write-up. Hoping that you visit us again in the near future. Those who liked our post please don't forget to pass it around. Thanks for taking the time to read it.

Book Your Installation